User Manual radio alarm clock Mystery MCR-23
 User Manual radio alarm clock Mystery MCR-23 |
User Manual radio alarm clock Mystery MCR-23
Features of the Mystery MCR-23 radio alarm clock: 0.6” (1.52 cm) display, FM tuner, quartz stabilizer, clock/timer, alarm clock, 2 alarm modes (radio/signal) and time image format - 24 hours.
Thank you for buying a radio alarm clock. Please read this manual carefully before turning on the device and starting operation. save the manual for future reference. Before plugging the device into the mains, check whether the voltage indicated on the radio corresponds to the voltage in the electrical network of your home. When unplugging the power cord from the outlet, hold on to the plug instead of the cord. If the appliance is not used for a long time, disconnect it from the mains. If you do not use the device for a long time, remove the batteries from the compartment.
Do not install the device in places where it may be exposed to water, humidity, heat, direct sunlight. Keep the device away from sources of magnetic fields (TV, speakers, magnetized objects). Do not expose the device to sudden temperature changes. Make sure that metal objects or liquids do not get inside the device body. If a foreign object or liquid gets into the case, disconnect the device, remove the batteries and contact the audio equipment maintenance and repair shop. When connected to the mains, there is a high voltage inside the device, which is life-threatening. When using the device, you need to be careful and follow these instructions. ID1 In order to avoid electric shock or fire, do not disassemble the device. If repairs are necessary, contact the service organization.
If temperature or humidity changes, condensation may form inside the device, which will lead to a short circuit. Keep the device at room temperature for 2 hours before use. Protect the device from dirt, bumps, scratches and damage during transportation. Do not place the appliance near heat sources. Observe the temperature range from -20 °C to +50 °C
Installed batteries can only provide short-term operation of the device in case of power outages. If the batteries have not been installed, then after a power outage, you will need to re-configure the device.
Dispose of used batteries in accordance with legal requirements.
After the device is connected to the network, the device will go into standby mode and “0:00” will start blinking on the screen. Setting the clock is only possible in standby mode. Press and hold the SET button until flashing symbols appear on the screen. Press the HR and MIN buttons sequentially to adjust the time and the SET button to confirm the selection.
Turn on the device. The radio will turn on at the last frequency used. The default frequency is 87.5Mhz. To switch to AM mode, press the BAND button. To manually select the desired radio frequency, press TUNING G/F sequentially. To manually search for radio stations (down or up the frequency range), press and hold the TUNING G/F button for 2-3 seconds. The device will search for the nearest radio station with a strong signal. To save radio stations in the device's memory, select the desired frequency, press and hold the SET button. Blinking symbols P01 will appear on the screen, select the number under which you want to save the radio station and press SET again to confirm the selection. To switch between the saved radio stations, press the MEM button sequentially. The level of reception of the radio signal depends on the environment, the place where the device is installed, and the distance from the broadcast source.
To set an alarm, the device must be in standby mode. Make sure that the clock has already been adjusted beforehand. Press and hold the AL1 or AL2 button until flashing symbols appear on the display. Press the HR and MIN buttons to adjust the hours and minutes and the AL1 (AL2) button to select the audio signal source (OFF - preset audio signal - radio). To check the set alarm time, press and hold the AL1 (AL2) button. The set time will start blinking on the display. To cancel the alarm, press the AL1 (AL2) button sequentially until the alarm indicator on the display goes out. Press the SNOOZE button while the alarm is running, and the alarm will be muted and will sound again after 9 minutes.
In accordance with the ongoing policy of continuous improvement of technical characteristics and design, the manufacturer reserves the right to make changes without prior notice. The device is assembled from modern and safe materials. At the end of its service life, in order to avoid possible harm to the life, health of the consumer, his property or the environment, the device must be disposed of separately from household waste in accordance with the waste disposal regulations in your region. We inform you that the entire packaging of this device is NOT INTENDED for secondary packaging or storage of food products in it. The service life is 3 years, provided that the product is used in strict accordance with this operating manual.
DOWNLOAD size 364 Kb "Radio alarm clock Mystery MCR-23 user manual"